HENSOTHERM® 7 KS Fabric 1000 E

Flexible cable bandage to form a fire penetration seal for cables and cable support structures
according to EN 1366-3

Inside buildings, especially in modern residential and office buildings, a large number of electrical cables run. Many cable sheaths and insulations are combustible and contribute to the spread of fire in case of fire. In addition, burning dripping of the cable sheaths and insulation can occur, as well as the release of toxic and highly corrosive fire gases, which can lead to smoke poisoning or attack technical equipment and other materials and impair their function.

HENSOTHERM® 7 KS Gewebe 1000 E is an A2 glass filament fabric coated on one side with intumescent HENSOTHERM® 7 KS fire protection coating. HENSOTHERM® 7 KS Fabric 1000 E is classified according to EN 1366-3 as a temporary and permanent fire penetration seal for electrical conduits, electrical installation pipes and cable support structures for a fire resistance duration of up to 120 minutes (ETA 22/0125) to restore the fire safety of massive wall structures provided with openings for electrical supply lines.

Kabeltrasse

Fire penetration seal in accordance with EN 1366-3

Rolle

HENSOTHERM® 7 KS Gewebe 1000 E

Application as fire protection bandage for electrical cables and cable support systems for encapsulation of toxic fire gases and to reduce burn-up of cable sheathing

Another possible application of HENSOTHERM® 7 KS Gewebe 1000 E is the use as a fire protection bandage for electrical lines and cable support systems to eliminate or reduce fire hazards.

/ KS Gewebe 1000 E Bündel

Electrical wiring without cable carriers

Kabeltrasse

Electrical wiring in cable carriers, installation prior to routing

Kabelztr

Electrical wiring in cable carriers with side arm

Kabeltrasse Wand

Electrical wiring in riser lines

For this purpose, HENSOTHERM® 7 KS Fabric 1000 E can be used as a full-surface cable sheathing in indoor and protected outdoor areas and inhibit the development of cable fires by reducing the burn-up of cable sheathing and insulation in the event of fire. The HENSOTHERM® 7 KS fire protection coating foams strongly at temperatures above approx. 150 °C and seals cavities around the cables with an insulating layer so that the fire is extinguished.

Complete wrapping of electrical cables, wiring systems and cable support structures (cable trays) with HENSOTHERM® 7 KS Fabric 1000 E can also reduce smoke release by encapsulating toxic fire gases.


Properties

  • Fire resistance class up to EI 120 tested according to EN 1366-3, ETA 22/0125
  • Classified as fire penetration seal in massive wall structures ≥ 10 cm
  • Single cables ≤ 80 mm
  • Cable bundles ≤ 100 mm
  • Flexible electrical installation conduits ≤ 20 mm
  • Cable trays ≤ 400 mm
  • Reduction of smoke gas release, encapsulation of toxic fire gases
  • No burning dripping of cable sheaths and insulation
  • Annular gap closure with gypsum filler
  • Indoor and protected outside area use
  • Can be painted over


Advantages

  • No pre-treatment or cleaning of cable systems required prior to application of the tape
  • Fire protection coating on the inside, outside made of insensitive glass fiber fabric easy to clean with a damp cloth
  • Easy re-application and inspection possible when using metal tapes or wires
  • Weather resistant (type X), resistant to moisture, frost and UV radiation for indoor and protected outdoor use
  • No need to measure the thickness of layers during installation (compared to fire protection coatings)
  • Installation also possible in case of lack of space, narrow bends or branches and restricted access
  • Easy to cut to size with knife or scissors
  • Extremely flexible, only 1 mm thick
  • Simple and economical solution


Environment

  • No protective film over the coating – fast installation, no waste
  • Meets eco-bau 1 and Minergie-eco requirements
  • Non-hazardous material according to GefStoffV, free of asbestos, lead, mercury and chromium
  • VOC according to LEED < 0.005 mg/m³
  • Solvent-, silicone-, halogen- and plasticizer-free
  • Green Product, VOC emission class A+


Delivery forms

  • Roll of 12 meters, 1 meter wide (weight 1.2 kg/m², 14.4 kg/roll)
Enquiry Obtain updates Recommendation Tender texts

Your recommendation

    Email address of the recipient (mandatory field)

    Your name (mandatory field)

    Your email address (mandatory field)

    Your message (mandatory field)

    The data will only be used to send the requested information to you. By entering the data and submitting the form, you confirm that you are entitled to pass on the recipient's e-mail address for this purpose.

    Privacy statement


    Your product enquiry

      Your name (mandatory field)

      Your email address (mandatory field)

      Your message (mandatory field)

      With this form you enter only the data necessary for the processing of your inquiry. These data will be used solely for the purpose of processing your request and will not be disclosed to third parties. The transmission of data is encrypted.

      Privacy statement

      Downloads


      Obtain updates

      You have the option here to register your name and your email address for update messages about the downloads of our material safety datasheets and declarations of performance. We use your personal data only for the purpose of sending you information per email about updated downloads, if appl.

      Sender, content and frequency
      The newsletters are sent directly by Rudolf Hensel GmbH and contain only information on the topics you have selected. The newsletter is mailed several times a year, different topics having different frequencies.

      Option to cancel
      You can cancel your newsletter subscription at any time for free, of course, and be deleted from the list.

      To do this, simply send an email with the subject “Austragen (Cancel)” to kundeninformation@rudolf-hensel.de. Alternatively, you can click on the “Austragen” (cancel) link in a newsletter, which is always to be found at the bottom of the email message.

      If you have any questions about our newsletter, feel free to contact us at contact@rudolf-hensel.de.

      Privacy Statement

       

      Request tender text for
      HENSOTHERM® 7 KS Fabric 1000 E

        Here you can request a tender text for
        our product. If you need the form urgently,
        please feel free to call us on +49(0)40 / 72 10 62 - 48.

        Your name (mandatory field)

        Your company (mandatory field)

        Your zip code (mandatory field)

        Your email address (mandatory field)

        Your phone number (mandatory field)

        With this contact form you enter only the data necessary for the processing of your inquiry. These data will be used solely for the purpose of processing your request and will not be disclosed to third parties. The transmission of data is encrypted.

        Privacy Statement

        • Contact

          Technical support / Sales
          Tel: +49 40 721062-48
          Fax: +49 40 721062-52
          Send email